![siemens hipath 3800 remove call forwarding from a station siemens hipath 3800 remove call forwarding from a station](https://www.manualsdir.com/manuals/142275/57/siemens-hipath-4000-page57.png)
A subset of up to 30 time slots may be switched to external traffic over the IP network. The board communicates with the common control function in the HiPath 4000 by means of the Ethernet network.The NCUI has switching capability of up to 256 time slots on 8 highways with 2.048 Mbps each within the local system. The board has the interface up to 16 peripheral cards in the LTU shelf and in addition an interface to support the 19-inch system. The NCUI performs central functions like DCL-LP, SIU, CONF, MTS and CG. It controls all peripheral boards in the local system, comparable to the LTUCE board in a peripheral shelf, and has access to the 10/100 Base-T Fast Ethernet Network. The Control Unit IP HiPath HG 3575 (NCUI) board is the main central control for the IPDA and gateway unit in a local system as part of a distributed PBX.Ī local system may be an LTU shelf or 19-inch boxes. Main central control for the IPDA and gateway unit in a local system as part of a distributed PBX.
![siemens hipath 3800 remove call forwarding from a station siemens hipath 3800 remove call forwarding from a station](https://res.cloudinary.com/engtips/image/fetch/w_800,c_lfill,q_auto,f_auto,g_faces:center/http://i41.tinypic.com/1z6t8g9.jpg)
Switching capability of up to 256 time slots on 8 highways The SLMAC board has SIPAC shelf connectors. It supports V.90 (56K) modems with data transmission rates up to 50 kilobits per second (Kbps) The SLMAC board generates its own ringing voltage and does not require an external ring generator. It allows stations to be 2.6 cable kilometres (1.6 cable-miles of #26 American Wire Gauge cable) from the system. It supports a line loop resistance of 1000 Ohms, which includes the resistance of the terminal equipment. This board can receive instructions from the operating system through the LTUCX board. The SLMAC board provides 24 analog channels. Dial pulse or DTMF analog single-line telephones.They support the following analog devices: These boards convert signals from analog-to-digital and from digital-to-analog. The new loadware solution means that only one SIUX hardware variant is necessary.Īn SLMAC board interfaces between the system and analog devices. 8 DTMF tone receivers/generators or 8 MFC tone receivers/generatorsĬountry-specific adaptions are implemented by means of different loadsware variants, which are loaded when the board is put into service.In the service unit, the SIUX has the following functions:
SIEMENS HIPATH 3800 REMOVE CALL FORWARDING FROM A STATION GENERATOR
The parameters for the different generator and receivers can be loaded during operation. The announcements can be stored directly on the SIUX.Īs part of the service unit (SU), the SIUX is installed in the CCS common control shelf.Īs a DTMF/MFC receiver, the board can be installed in any desired peripheral board slot of the SWU. In addition, it contains dial tone receivers, DTMF receivers, a test generator and a test receiver.
![siemens hipath 3800 remove call forwarding from a station siemens hipath 3800 remove call forwarding from a station](https://s3.manualzz.com/store/data/026934257_1-2eab21032e335da93772aa14d9acb21d.png)
The signaling unit SIUX is used to supply the system with audible tones, announcements and music on hold. The SIUX ( Signaling Unit) board for Hicom 300/300E, replaces the SIU board in the central and peripheral system shelves.